-40%

E-Z EASY PULL CLUTCH KIT EASYBOY LITE HARLEY DAVIDSON BIG TWIN SPORTSTER 73304

$ 7.91

Availability: 201 in stock
  • Condition: New
  • Country/Region of Manufacture: Taiwan
  • Manufacturer Part Number: 73304
  • Refund will be given as: Money Back
  • Item must be returned within: 30 Days
  • Return shipping will be paid by: Buyer
  • Returns Accepted: Returns Accepted
  • Brand: V-Factor
  • UPC: Does Not Apply
  • Surface Finish: Metal

    Description

    ​​​​​​​​​​​​​​
    Motorcycle Parts Direct
    E-Z EASY PULL CLUTCH KIT EASYBOY LITE HARLEY DAVIDSON BIG TWIN SPORTSTER 73304
    Motorcycle Parts Direct
    Your #1 Supplier of Aftermarket Parts and Accessories for Harley-Davidsons
    High Quality
    Best Prices
    Fast Shipping
    EASYBOY EASY BOY LITE E-Z PULL CLUTCH LEVER KIT
    FOR HARLEY DAVIDSON BIG TWIN & SPORTSTER
    This kit reduces by 40% the effort required to pull the clutch lever, reducing rider fatigue and offering smoother, easier clutch action
    Kit fits inside the transmission side cover and extends the clutch operating mechanism for improved leverage
    Fits all Big Twin 5 speed (except FXR models) 1987/2006 & Sportster 1986/1990
    Mid-USA # 73304
    INSTALLATION INSTRUCTIONS:
    1. You will need to loosen and or remove the exhaust system as necessary to clear the right side transmission cover.
    2. Drain the transmission oil. (With bike on jiffy stand you will only loose a small amount of fluid.  (I DO NOT drain the entire tranny, just replace what little drains out from the cover.)
    3. Completely loosen the clutch cable adjuster.
    4. Remove the 6 bolts that hold the transmission cover and remove cover.
    5. Remove the large “C” clip that retains the ball and ramp mechanism. Lift out the ramp and cable coupling, being careful no to lose the three ball bearings. Disconnect the coupling from the clutch cable.
    6. Unscrew the clutch cable from the transmission cover and remove the o-ring. Do not discard o-ring as it will be reused.
    7. Install the E-Z Clutch Assist adapter piece on the ramp piece as shown in photo below. Be sure that the bolt is tightened to 10-12 ft-lbs.
    8. Slide the spacer from the kit onto the end of the clutch cable. Carefully screw the cable end back into the transmission cover. Re-install the o-ring. Screw the cable end back into the transmission cover. Do not over tighten.
    9. Attach the cable coupler to the clutch cable end and attach the coupler to the V-Twin Mfg. E-Z Pull Clutch Assist arm. Install the ramp mechanism and 3 bearings into the transmission cover and replace the “C” clip.
    10.Using a new transmissions side gasket replace the transmission cover: Torque the cover screws to 7-9 ft-lbs and refill transmission oil to the correct level.
    11. Refer to your service manual for clutch adjustment.
    12.Replace and re-tighten the exhaust system as necessary.
    Payment
    We would really like to be paid within 5 days of the sale. We accept Paypal, Mastercard, Visa, and Discover. We really prefer PAYPAL because it protects you and us in case there's a problem. Tennessee residents have to pay 9.25% sales tax
    .
    ​​​​​​​
    Things to Know
    Shipping
    Returns
    We offer FREE shipping on all orders!
    Your order will be shipped within 1 working day of receiving payment (Monday-Friday). Most orders are shjipped via USPS 1st Class Mail or USPS Priority Mail.  Tracking numbers will be sent to you by ebay and/or Paypal.  All items are sent to the address on file with ebay.  Any item returned because of an address error will be re-shipped upon payment of actual shipping cost.  International take longer, from 5 to 21 days.  Please be patient as we have no control over shipping once it leaves our warehouse.  Any import taxes or duties are the responsiblility of the buyer.
    If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange within 60 days.  To return an item please use EBAY RETURNS.  Items must be in original packaging and in the same condition, new, as received.  We cannot offer a refund on parts that have been damaged in any way by the buyer.
    ​​​​​​​
    R
    eturns that are not damaged or defective are subject to a 20% restocking fee.
    Stuff you need to know
    About us
    We are a  bike shop in Tennessee specializing in Harleys. Our suppliers include Custom Chrome, MidWest, Mid USA, DNA and Kuryakyn.  For specific questions about whether this part will fit your bike or custom application, please check the listing, with your local Harley dealer, or your local mechanic.  They know your exact bike better than we do.
    Non-stock special order items may be subject to the manufacturer's  restocking charges. We are not responsible for any charges for labor, repairs, materials, down-time or lost profits due to returning any merchandise.  We use the manufacturer’s statement regarding fitment. We can only guarantee what the manufacturer or supplier says it will fit. Please make sure the part is listed as fitting your bike. If we said it would, and it doesn’t we will refund your money. A lot of parts can be customized to fit other models, if you have the skills, however you do this AT YOUR OWN RISK
    High Quality
    Best Prices
    Fast Shipping
    See our other items
    EASYBOY EASY BOY LITE E-Z PULL CLUTCH LEVER KIT FOR HARLEY DAVIDSON BIG TWIN & SPORTSTER This kit reduces by 40% the effort required to pull the clutch lever, reducing rider fatigue and offering smoother, easier clutch action Kit fits inside the transmission side cover and extends the clutch operating mechanism for improved leverage Fits all Big Twin 5 speed (except FXR models) 1987/2006 & Sportster 1986/1990 Mid-USA # 73304 INSTALLATION INSTRUCTIONS: 1. You will need to loosen and or remove the exhaust system as necessary to clear the right side transmission cover. 2. Drain the transmission oil. (With bike on jiffy stand you will only loose a small amount of fluid. (I DO NOT drain the entire tranny, just replace what little drains out from the cover.) 3. Completely loosen the clutch cable adjuster. 4. Remove the 6 bolts that hold the transmission cover and remove cover. 5. Remove the large “C” clip that retains the ball and ramp mechanism. Lift out the ramp and cable coupling, being careful no to lose the three ball bearings. Disconnect the coupling from the clutch cable. 6. Unscrew the clutch cable from the transmission cover and remove the o-ring. Do not discard o-ring as it will be reused. 7. Install the E-Z Clutch Assist adapter piece on the ramp piece as shown in photo below. Be sure that the bolt is tightened to 10-12 ft-lbs. 8. Slide the spacer from the kit onto the end of the clutch cable. Carefully screw the cable end back into the transmission cover. Re-install the o-ring. Screw the cable end back into the transmission cover. Do not over tighten. 9. Attach the cable coupler to the clutch cable end and attach the coupler to the V-Twin Mfg. E-Z Pull Clutch Assist arm. Install the ramp mechanism and 3 bearings into the transmission cover and replace the “C” clip. 10.Using a new transmissions side gasket replace the transmission cover: Torque the cover screws to 7-9 ft-lbs and refill transmission oil to the correct level. 11. Refer to your service manual for clutch adjustment. 12.Replace and re-tighten the exhaust system as necessary.
    ​​​​​​​​​​​​​​
    Motorcycle Parts Direct
    E-Z EASY PULL CLUTCH KIT EASYBOY LITE HARLEY DAVIDSON BIG TWIN SPORTSTER 73304
    EASYBOY EASY BOY LITE E-Z PULL CLUTCH LEVER KIT
    FOR HARLEY DAVIDSON BIG TWIN & SPORTSTER
    This kit reduces by 40% the effort required to pull the clutch lever, reducing rider fatigue and offering smoother, easier clutch action
    Kit fits inside the transmission side cover and extends the clutch operating mechanism for improved leverage
    Fits all Big Twin 5 speed (except FXR models) 1987/2006 & Sportster 1986/1990
    Mid-USA # 73304
    INSTALLATION INSTRUCTIONS:
    1. You will need to loosen and or remove the exhaust system as necessary to clear the right side transmission cover.
    2. Drain the transmission oil. (With bike on jiffy stand you will only loose a small amount of fluid.  (I DO NOT drain the entire tranny, just replace what little drains out from the cover.)
    3. Completely loosen the clutch cable adjuster.
    4. Remove the 6 bolts that hold the transmission cover and remove cover.
    5. Remove the large “C” clip that retains the ball and ramp mechanism. Lift out the ramp and cable coupling, being careful no to lose the three ball bearings. Disconnect the coupling from the clutch cable.
    6. Unscrew the clutch cable from the transmission cover and remove the o-ring. Do not discard o-ring as it will be reused.
    7. Install the E-Z Clutch Assist adapter piece on the ramp piece as shown in photo below. Be sure that the bolt is tightened to 10-12 ft-lbs.
    8. Slide the spacer from the kit onto the end of the clutch cable. Carefully screw the cable end back into the transmission cover. Re-install the o-ring. Screw the cable end back into the transmission cover. Do not over tighten.
    9. Attach the cable coupler to the clutch cable end and attach the coupler to the V-Twin Mfg. E-Z Pull Clutch Assist arm. Install the ramp mechanism and 3 bearings into the transmission cover and replace the “C” clip.
    10.Using a new transmissions side gasket replace the transmission cover: Torque the cover screws to 7-9 ft-lbs and refill transmission oil to the correct level.
    11. Refer to your service manual for clutch adjustment.
    12.Replace and re-tighten the exhaust system as necessary.
    Motorcycle Parts Direct
    Your #1 Supplier of Aftermarket Parts and Accessories for Harley-Davidsons
    Fast Shipping
    High Quality
    Best Prices
    See our other items
    We offer FREE shipping on all orders!
    Your order will be shipped within 1 working day of receiving payment (Monday-Friday). Most orders are shjipped via USPS 1st Class Mail or USPS Priority Mail.  Tracking numbers will be sent to you by ebay and/or Paypal.  All items are sent to the address on file with ebay.  Any item returned because of an address error will be re-shipped upon payment of actual shipping cost.  International take longer, from 5 to 21 days.  Please be patient as we have no control over shipping once it leaves our warehouse.  Any import taxes or duties are the responsiblility of the buyer.
    If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange within 60 days.  To return an item please use EBAY RETURNS.  Items must be in original packaging and in the same condition, new, as received.  We cannot offer a refund on parts that have been damaged in any way by the buyer.
    ​​​​​​​
    R
    eturns that are not damaged or defective are subject to a 20% restocking fee.
    Stuff you need to know
    About us
    Non-stock special order items may be subject to the manufacturer's  restocking charges. We are not responsible for any charges for labor, repairs, materials, down-time or lost profits due to returning any merchandise.  We use the manufacturer’s statement regarding fitment. We can only guarantee what the manufacturer or supplier says it will fit. Please make sure the part is listed as fitting your bike. If we said it would, and it doesn’t we will refund your money. A lot of parts can be customized to fit other models, if you have the skills, however you do this AT YOUR OWN RISK
    We are a  bike shop in Tennessee specializing in Harleys. Our suppliers include Custom Chrome, MidWest, Mid USA, DNA and Kuryakyn.  For specific questions about whether this part will fit your bike or custom application, please check the listing, with your local Harley dealer, or your local mechanic.  They know your exact bike better than we do.
    EASYBOY EASY BOY LITE E-Z PULL CLUTCH LEVER KIT
    FOR HARLEY DAVIDSON BIG TWIN & SPORTSTER
    This kit reduces by 40% the effort required to pull the clutch lever, reducing rider fatigue and offering smoother, easier clutch action
    Kit fits inside the transmission side cover and extends the clutch operating mechanism for improved leverage
    Fits all Big Twin 5 speed (except FXR models) 1987/2006 & Sportster 1986/1990
    Mid-USA # 73304
    INSTALLATION INSTRUCTIONS:
    1. You will need to loosen and or remove the exhaust system as necessary to clear the right side transmission cover.
    2. Drain the transmission oil. (With bike on jiffy stand you will only loose a small amount of fluid.  (I DO NOT drain the entire tranny, just replace what little drains out from the cover.)
    3. Completely loosen the clutch cable adjuster.
    4. Remove the 6 bolts that hold the transmission cover and remove cover.
    5. Remove the large “C” clip that retains the ball and ramp mechanism. Lift out the ramp and cable coupling, being careful no to lose the three ball bearings. Disconnect the coupling from the clutch cable.
    6. Unscrew the clutch cable from the transmission cover and remove the o-ring. Do not discard o-ring as it will be reused.
    7. Install the E-Z Clutch Assist adapter piece on the ramp piece as shown in photo below. Be sure that the bolt is tightened to 10-12 ft-lbs.
    8. Slide the spacer from the kit onto the end of the clutch cable. Carefully screw the cable end back into the transmission cover. Re-install the o-ring. Screw the cable end back into the transmission cover. Do not over tighten.
    9. Attach the cable coupler to the clutch cable end and attach the coupler to the V-Twin Mfg. E-Z Pull Clutch Assist arm. Install the ramp mechanism and 3 bearings into the transmission cover and replace the “C” clip.
    10.Using a new transmissions side gasket replace the transmission cover: Torque the cover screws to 7-9 ft-lbs and refill transmission oil to the correct level.
    11. Refer to your service manual for clutch adjustment.
    12.Replace and re-tighten the exhaust system as necessary.